Pagsasalin
I-edit ang Pagsasalin
ayon kay 
Shell mold casting, also referred to commonly as shell molding, is comparatively a new casting technique, developed in Germany in the 1940s.
It’s a type of metal casting process that involves pouring molten metal(ferrous or non-ferrous) or alloy into sand and resin which is further heated and shaped to build a mold.
Shell mold casting offers improved surface finish and higher precision compared to other metal casting methods, and suitable for small parts that require complex shapes and high dimensional accuracy.
Shell mold casting is applied to various industries such as aerospace, medikal na, at industriya ng automotive.
It is especially popular in the automotive industry and is often employed to manufacture camshafts, gearboxes, mga crankshaft, mga ulo ng silindro, bearing housings, lever arms, and valve bodies.
Two matching metal pattern halves—typically machined from steel or iron—are produced to the exact geometry of the desired casting (plus allowances for shrinkage and shell thickness).
Each pattern half is heated (≈180–250 °C), lightly sprayed with a release agent, then dipped into a “dump box” containing fine sand coated in a thermosetting resin.
The hot pattern cures a uniform shell layer (6–12 mm thick) as excess sand is shaken off.
The two cured shell halves are carefully stripped from their patterns.
If internal cavities are required, resin‐bonded sand cores are placed inside one shell half.
The cope (top) and drag (bottom) shells are then clamped together in a flask, and the gating system (sprue, mga runners, vents) is attached.
Molten metal or alloy (hal., bakal na bakal, bakal na bakal, aluminyo) is heated to its liquidus temperature and poured by gravity into the sprue.
The metal fills the shell cavity, replicating fine details and thin sections.
The thin, ceramic‐like shell conducts heat away rapidly.
After an appropriate cooling interval—often just a few minutes at ambient temperature—the metal has solidified into a robust casting.
The flask is opened and the shell fragments are broken away to free the casting.
The part is then freed of any gating or core material and undergoes any required trimming, paggiling ng mga, or surface finishing before inspection.
Shell molding accommodates most ferrous and non-ferrous alloys, halimbawa na lang:
| Alloy Family | Typical Grades | Key Properties & Applications |
|---|---|---|
| Gray Iron | ASTM A48 Class 20–40 | Excellent machinability & vibration damping; used for engine blocks, mga pabahay. |
| Ductile Iron | ASTM A536 60-40-18, 65-45-12 | Higher strength & toughness than gray iron; ideal for gears, mga crankshaft, Mga balbula. |
| Carbon Steel | AISI 1018, 1020, 1045 | Good strength and weldability; used for shafts, mga panaklaw, structural parts. |
| haluang metal na bakal | 4140, 4340, H13 | Enhanced hardness, tigas na tigas, at magsuot ng resistensya; used in dies, mga tooling, mabigat na makinarya. |
| Hindi kinakalawang na asero | 304, 316, 17-4PH, 2205 (Duplex) | Corrosion resistance and strength; used in chemical, pagkain, medikal na, and marine parts. |
| Mga Alloys ng Aluminyo | A356, A357, ADC12 | Magaan ang timbang, good fluidity; used for automotive brackets, mga pabahay, aerospace fittings. |
| Mga Alloy ng Copper | C905 (Tin Bronze), C836 (Aluminyo Bronze), C230 (Cartridge Brass) | Excellent wear and corrosion resistance; ginagamit sa mga bearings, mga bushing, hardware ng dagat. |
| Nickel-Based Alloys | Inconel 625, Hastelloy C276 | Outstanding high-temperature strength and corrosion resistance; used in aero-engines, pagproseso ng kemikal. |
| Mga haluang metal ng magnesiyo | AZ91D, AM60 | Very lightweight; used in electronics housings and automotive components. |
| Zinc Alloys | Zamak 3, Zamak 5 | Low melting point and excellent detail reproduction; used for small, masalimuot na mga bahagi (hardware, mga angkop na bagay). |
1. Proprietary Resin‐Sand Formulations
2. High-Speed, Automated Shell Production
3. Expert Pattern & Tooling Design
4. Broad Alloy Capability
5. Tight Dimensional Control
6. Lean, Green Operations
7. Comprehensive Quality Assurance
8. Dedicated Technical Support
| Industriya ng Industriya | Typical Shell Mold Castings | Typical Products |
|---|---|---|
| Automotive | Camshaft and crankshaft housings, gearbox and transmission cases, mga ulo ng silindro, bearing carriers, and linkage arms—benefit from tight tolerances and fine surface finish, reducing or eliminating post-machining. |  |
| Aerospace & Defense | Actuator brackets, fuel-system fittings, small turbine stator segments, control-surface hinges, and structural brackets—leveraging weight-sensitive, high-precision parts where repeatability and fatigue resistance are critical. |  |
| Mga Medikal na Kagamitan | Surgical instrument handles and housings, implant-fixture bushings, orthopedic bracketry, and fluid-control valves—requiring complex internal passages, biocompatible alloys, and sterilizable finishes. |  |
| Industrial Valves & Pumps | Precision valve bodies, mga impeller, volutes, and pump housings cast in stainless or duplex stainless steels—resisting corrosive media while maintaining exacting dimensional requirements for reliable sealing and flow control. |  |
| Oil & Gas / Petrochemical | Chemical-service fittings, filter housings, manifold blocks, and instrumentation flanges—taking advantage of exotic alloys (hal., Inconel, Bilisan mo na) with minimal surface porosity and high dimensional fidelity. |  |
| Consumer & Decorative | Ornamental door handles, mga fixture sa pag iilaw, sculpture components, and architectural accents—shell-cast in brass, tanso, or aluminum to capture fine textures and crisp edges. |  |
| Renewable Energy & Power Generation | Small hydraulic turbine nozzles, control-valve bodies, and generator accessory brackets—benefiting from rapid turnaround and the ability to cast heat-resistant alloys with tight wall-thickness control. |  |
| Same side of parting line: | ± .020 for 1st 3″ | Add ± .003 / inch over 3″ |
| Across parting line: | ± .030 for 1st 3″ | ± .003 / inch over 3″ |
| Draft: | Typically 1° | Certain applications at 0° draft. |
| Typical Finish Stock: | .060″ maximum | |
| Hole size cast into part: | DIAMETER | DEPTH |
| Less than 0.5″ | Equal to diameter | |
| 0.5″ – 1.0″ | Equal to 1.5 times diameter | |
| Greater than 1.0″ | Equal to 2 times diameter |
Shell mold casting is a precision sand-based process in which a heated metal pattern is coated with fine, resin-bonded sand to form thin “shell” halves. Once cured and assembled, these shells serve as the mold into which molten metal is poured.
Almost any alloy is suitable—including gray and ductile irons, carbon and alloy steels, hindi kinakalawang na asero, aluminyo alloys, copper-based alloys, and even nickel-based superalloys—thanks to the shell’s heat resistance.
Typical dimensional tolerances reach ±0.3 mm per 100 mm, and surface finishes are in the Ra 3–6 µm range. This precision often eliminates or minimizes secondary machining.
Shell molding excels at small to medium components (from a few grams up to about 50 kg). Shell halves larger than this become difficult to handle and may crack under their own weight.
Each shell half cures in roughly 10–30 seconds on automated dip-and-shake equipment. This quick turnaround supports fast prototyping and moderate production volumes.
Intricate details—thin walls (down to 1.5 mm), Mga Undercut, fine ribs, and internal passages—are readily achieved. Cores can be inserted for complex internal cavities.
Select shell molding when your parts require small- to medium-size, mataas na dimensional katumpakan, fine surface quality, and complex detail.
| Mga Criteria | buhangin paghahagis | Shell amag paghahagis | Pamumuhunan sa Paghahagis |
|---|---|---|---|
| Mold Material | Green sand (silica + clay) | Resin-bonded fine sand shell | Ceramic shell (wax patterns dipped in slurry) |
| Gastos sa Tooling | Very low | Katamtaman (heated patterns + resin sand) | Mataas na (wax tooling + multiple shell dips) |
| Mold Reuse | Hindi (sand broken each pour, but sand is reclaimable) | Hindi (each shell single-use, sand reclaimable) | Hindi (each ceramic shell single-use) |
| Part Size Range | Very small to very large (> several tons) | Small to medium (up to ~50 kg) | Very small to small (karaniwan < 10 kg) |
| Dimensional Tolerance | ± 0.5 mm per 100 mm | ± 0.25–0.35 mm per 100 mm | ± 0.15–0.25 mm per 100 mm |
| Tapos na sa ibabaw (Ra) | 6–12 µm | 3–6 µm | 1–2 µm |
| Kapal ng pader | ≥ 6 mm | ≥ 1.5–2 mm | ≥ 1 mm |
| Complexity & Detail | Katamtaman (cores required for internal features) | Mataas na (manipis na pader, fine features easily achieved) | Napakataas na (Mga Undercut, intricate geometries) |
| Oras ng Pag-ikot | Mabagal (mold prep, pag-iling) | Mabilis na (shell cures in seconds) | Slowest (multiple coating and dewax steps) |
| Dami ng Produksyon | Mababa hanggang sa katamtaman | Mababa hanggang sa katamtaman | Mababa hanggang sa katamtaman (100–1,000s parts) |
| Typical Alloys | Bakal na Bakal, bakal na bakal, aluminyo, tanso, atbp. | Bakal na Bakal, bakal na bakal, stainless, aluminyo, mga haluang metal ng tanso | Stainless, Superalloys, tanso, aluminyo |
| Post-processing Needs | Often heavy machining and surface cleanup | Minimal machining; light finishing | Minimal machining; often ready to final shape |
| Best For | Large, heavy, cost-sensitive parts | Precision small/medium parts with moderate volume | Extremely intricate, thin-walled, high-accuracy parts |
Karapatang-ari © 2024 DEZE Technology Co., Ltd Lahat ng karapatan ay nakalaan.
Mag iwan ng Tugon